{"id":42066,"date":"2016-07-13T00:00:33","date_gmt":"2016-07-13T00:00:33","guid":{"rendered":"https:\/\/namgar.com\/NAMGAR2020\/?p=42066"},"modified":"2016-07-13T00:00:33","modified_gmt":"2016-07-13T00:00:33","slug":"fuel-leaks-from-mga-carbs-how-float-bowl-to-carb-assembly-can-be-confusing","status":"publish","type":"post","link":"https:\/\/namgar.com\/NAMGARMAIN\/fuel-leaks-from-mga-carbs-how-float-bowl-to-carb-assembly-can-be-confusing\/","title":{"rendered":"Fuel Leaks From MGA Carbs &#8211; How Float Bowl to Carb Assembly Can Be Confusing"},"content":{"rendered":"<p><img decoding=\"async\" loading=\"lazy\" src=\"https:\/\/namgar.com\/NAMGAR2020\/wp-content\/uploads\/2020\/08\/FuelLeak_P1060967_cropped_220-220x184-1.jpg\" alt=\"Fuel Leaks From MGA Carbs - How Float Bowl to Carb Assembly Can Be Confusing\" width=\"220\" height=\"184\" class=\"alignleft size-full wp-image-42067\" \/>A recent phone call from a fellow CCMGC member brought to my attention the potential for confusion. The member said he smelled fuel when his car was stopped, and when he opened the bonnet he could see fuel dripping from both carburetors.<\/p>\n<p>I immediately knew what his problem was, and told him it was OK to drive his car to my garage, as the fuel would not be dripping while he was driving.<\/p>\n<p>When he arrived, and the car had cooled down a little, I gave him the correct size socket (9\/16\u201d or 14mm), and told him to remove the bolt holding the float bowl to the carb body. I suspected that the rubber grommets (2 per carb) had hardened. In fact, they were in good condition as he has only had the car for about one year, and it was rebuilt shortly before he purchased it.<\/p>\n<p>What we did find was that the arrangement around the rubber grommets was incorrect. His assembly sequence, from the top to the bottom of the hold-up bolt on both carbs was:<\/p>\n<ul>\n<li>Fiber washer<\/li>\n<li>Rubber grommet<\/li>\n<li>Rubber grommet<\/li>\n<li>Steel washer<\/li>\n<\/ul>\n<p>The steel washer was flat, not concave as it should be. This concave washer must be fitted with the dished side up. (I have seen them fitted upside down). We made two concave washers from his flat washers using a suitably sized socket, a suitably sized nut, and a vice, to put a dish in them. We then re-assembled the float bowls to the carb bodies, leaving off the fiber washers. The final assembly was simply:<\/p>\n<ul>\n<li>Rubber grommet<\/li>\n<li>Rubber grommet<\/li>\n<li>Concave steel washer<\/li>\n<\/ul>\n<p>This did the trick, and there were no more leaks.<\/p>\n<p>The assembly confusion arises for several reasons:<\/p>\n<ol>\n<li>Later cars did not have a banjo bolt, but instead had a stud screwed into the carb body.<\/li>\n<li>With the stud arrangement, there was an extra steel washer above the top grommet.<\/li>\n<li>It is not clear from the parts book, or from suppliers\u2019 catalogs, whether these 2 steel washers were flat or concave.<\/li>\n<li>In fact the parts book I have (AKD1055), shows the banjo bolt arrangement with a fiber washer (AUC1137) in the location of the dished steel washer. Perhaps the fiber washer was replaced later with a steel dished washer for better sealing of the grommets. The Workshop Manual (AKD600) appears to show a single concave steel washer at the bottom, not a fiber washer.<\/li>\n<\/ol>\n<p>The diagram below from Burlen Fuel Systems, shows the three different arrangements.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" src=\"https:\/\/namgar.com\/NAMGAR2020\/wp-content\/uploads\/2020\/08\/FuelLeaks_CarburettorDiagram_500.jpg\" alt=\"Carburetter Components\" width=\"500\" height=\"395\" class=\"aligncenter size-full wp-image-42068\" srcset=\"https:\/\/namgar.com\/NAMGARMAIN\/wp-content\/uploads\/2020\/08\/FuelLeaks_CarburettorDiagram_500.jpg 500w, https:\/\/namgar.com\/NAMGARMAIN\/wp-content\/uploads\/2020\/08\/FuelLeaks_CarburettorDiagram_500-300x237.jpg 300w\" sizes=\"auto, (max-width: 500px) 100vw, 500px\" \/><\/p>\n<p>The grommets themselves used to be rubber, but modern fuel with 5-15% ethanol content eats these rubbers in a short time. I had a new set of grommets from an SU rebuild kit last less than 2,000 miles before they started leaking. Current suppliers such as MOSS or Scarborough Faire supply grommets made of Viton\u00ae , which are supposed to be ethanol resistant (like similar fuel tank sender gaskets).<\/p>\n","protected":false},"excerpt":{"rendered":"<p>A recent phone call from a fellow CCMGC member brought to my attention the potential<\/p>\n","protected":false},"author":1,"featured_media":44346,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"nf_dc_page":"","ngg_post_thumbnail":0,"footnotes":""},"categories":[14],"tags":[],"class_list":["post-42066","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-featured-tech-sessions"],"_links":{"self":[{"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/posts\/42066","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/comments?post=42066"}],"version-history":[{"count":0,"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/posts\/42066\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/media\/44346"}],"wp:attachment":[{"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/media?parent=42066"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/categories?post=42066"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/namgar.com\/NAMGARMAIN\/wp-json\/wp\/v2\/tags?post=42066"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}